Jewellery nickel, cadmium and lead regulations: EU and UK limits

Jewellery nickel and cadmium regulations in the EU and UK come from REACH Annex XVII. Entry 27 limits how much nickel jewellery can release onto the skin, entry 23 caps cadmium in metal parts at 0.01% by weight, and entry 63 caps lead in any individual part at 0.05% by weight. Great Britain applies the same restrictions through UK REACH. On top of that, GPSR in the EU and the General Product Safety Regulations 2005 in Great Britain require the product to be safe and traceable.

This guide is for jewellery brands and Amazon sellers outside the UK and EU selling earrings, necklaces, rings, bracelets, watches and hair accessories into either market. If you need an EU or UK name and address for your labels and listings, see our EU and UK Responsible Person service.

Metal limits for jewellery under REACHA bar chart comparing nickel release limits under REACH entry 27, in micrograms per square centimetre per week: below 0.2 for piercing post assemblies and no more than 0.5 for items in direct and prolonged skin contact. Coated items must keep release within 0.5 for at least two years of normal use. Below the chart, two panels: cadmium under entry 23 is limited to below 0.01% by weight of metal, and lead under entry 63 to below 0.05% by weight in each part. The same limits apply in Great Britain under UK REACH.Metal limits for jewelleryNickel releaseREACH entry 27, µg per cm² per weekPiercing posts0.2Skin contact items0.5Coated items: within 0.5 for 2 years of normal useCadmium0.01%by weight of metalREACH entry 23Lead0.05%by weight, each partREACH entry 63Same limits in Great Britain under UK REACH
REACH limits for nickel release, cadmium and lead in jewellery. Products must be below these limits.

Who the jewellery metal limits apply to

The cadmium and lead restrictions cover jewellery and imitation jewellery articles and hair accessories, including bracelets, necklaces, rings, piercing jewellery, wrist watches and wrist-wear, brooches and cufflinks. Both also apply to metal beads and other components sold for jewellery making, so suppliers of findings and craft parts are caught too.

The nickel restriction is wider. It covers piercing post assemblies and any article intended to come into direct and prolonged contact with the skin, which includes earrings, necklaces, bracelets, rings, watch cases and straps, and also clothing parts such as rivets and zips.

Anyone placing these products on the market is responsible for meeting the limits. GB Trading Standards guidance says manufacturers and importers are normally expected to test, while other sellers should check compliance with their supplier, for example by asking for test certificates. It says doing nothing is not enough.

The laws that apply

TopicEUGreat Britain
Nickel releaseREACH Annex XVII entry 27: below 0.2 µg/cm²/week for piercing posts; no more than 0.5 µg/cm²/week for prolonged skin contactUK REACH, same limits
CadmiumREACH Annex XVII entry 23: below 0.01% by weight of the metalUK REACH, same limit
LeadREACH Annex XVII entry 63: below 0.05% by weight in any individual partUK REACH, same limit
General product safetyGeneral Product Safety Regulation (EU) 2023/988General Product Safety Regulations 2005
Precious metal markingNational rules, which vary between member statesHallmarking Act 1973

Nickel release limits explained

Nickel is a common cause of contact allergy, so the rule limits how much nickel the item releases, not how much it contains. There are two limits:

  • Piercing post assemblies: release must be below 0.2 µg/cm²/week. The post assembly is the part inserted into the piercing plus any parts that hold the piece against the wound, such as a butterfly or ball.
  • Items in direct and prolonged skin contact: release must not exceed 0.5 µg/cm²/week.

Plated or coated items with a nickel-bearing base metal are allowed only if the coating keeps release within the 0.5 limit for at least two years of normal use. Testing for release uses EN 1811, and the abrasion and corrosion method for coated items is EN 12472. If your supplier only gives you a nickel content figure, ask for a release test instead.

Cadmium and lead limits

Cadmium must not be present at 0.01% or more by weight of the metal in metal beads and components for jewellery making, or in metal parts of jewellery, imitation jewellery and hair accessories. The restriction does not apply to articles placed on the market before 10 December 2011, or to jewellery that was more than 50 years old on that date.

Lead must not be present at 0.05% or more by weight in any individual part, which includes base materials and components. There are exemptions for crystal glass, internal watch components that consumers cannot reach, non-synthetic or reconstructed precious and semi-precious stones not treated with lead, and enamels. Articles first placed on the market before 9 October 2013 are also exempt.

Low-cost alloy jewellery, especially zinc alloys and solders, is where cadmium and lead failures tend to show up, so test each alloy rather than each design.

What your test reports and labels need

  • A nickel release report to EN 1811 for each skin-contact metal, with EN 12472 pre-treatment for coated items.
  • Cadmium and lead content reports covering every metal part, including findings, clasps and solder.
  • A GPSR risk assessment that covers the materials, small parts and who is likely to use the product.
  • A type, batch or serial number on the product or, where it is too small, its packaging or accompanying document.
  • The manufacturer’s name and postal and electronic address, and the responsible person’s details where you are outside the market.

For gold, silver, platinum and palladium sold in Great Britain, the Hallmarking Act 1973 also applies. Articles at or above the exemption weights (1 g for gold, 7.78 g for silver, 0.5 g for platinum and 1 g for palladium) must be hallmarked before they can be described as precious metal. Hallmarks from EEA countries are accepted only if applied before 31 December 2020, though marks under the international Hallmarking Convention are accepted.

The responsible person and economic operator angle

Under EU GPSR, jewellery cannot be placed on the EU market unless there is an economic operator established in the EU responsible for it. For a brand outside the EU, that is usually an importer or an authorised representative, often called the EU responsible person. Their name and contact details go on the product, packaging or accompanying document, and on your online listings. Our GPSR label template guide shows how to fit the details on small items.

In Great Britain the General Product Safety Regulations 2005 make the UK representative, or failing that the importer, the producer when the manufacturer is outside the UK. An EU representative does not cover Great Britain, so a brand selling in both needs both. Our guide to UK Responsible Person requirements explains the difference.

Common Amazon listing and compliance pitfalls

  • “Nickel free” with no evidence. If you claim it, have a release test to back it, and remember nickel free is a marketing claim, not the legal test.
  • One report for a whole range. A report on one alloy does not cover a different alloy or plating supplier.
  • Testing content, not release. The nickel limit is about release from the surface over time.
  • Forgetting the findings. Clasps, ear wires and solder are parts too, and lead and cadmium limits apply to each one.
  • Calling it silver or gold. In Great Britain, describing an unhallmarked item over the exemption weight as precious metal is an offence. Plated items should be described as plated.
  • No EU or UK address. Amazon’s EU stores ask for an EU responsible person on GPSR listings, and listings without one can be blocked.
  • Packaging. Gift boxes and pouches count as packaging. See our EPR registration service.

Jewellery compliance checklist

  • List every metal and coating in each design, including findings and solder.
  • Get nickel release reports for skin-contact parts and piercing posts.
  • Get cadmium and lead content reports for every metal part.
  • Check exemptions before relying on them, for example for stones or crystal glass.
  • Hallmark precious metal items over the exemption weight before selling them in Great Britain.
  • Complete a GPSR risk assessment and keep it with the reports in your technical file.
  • Add batch numbers, manufacturer details and your EU or UK responsible person’s details.
  • Check your listing claims, such as nickel free or sterling silver, match your evidence.

Your next step

If you sell jewellery into the EU or Great Britain from outside, EU Brand Support can act as your EU or UK Responsible Person, giving you an address for labels and listings and holding your test reports for authority requests. Our Jewellery compliance template pack includes Declaration of Conformity, risk assessment and technical file checklist templates in EU and UK versions. For chemical mixtures such as jewellery cleaners, see our CLP labelling service. Not sure where your product sits? Get in touch.

This guide is general information, not legal advice. Check the rules for your specific product.

Frequently asked questions

What is the nickel limit for earrings?

For the post that goes through the piercing, nickel release must be below 0.2 µg/cm²/week. Other parts of the earring in prolonged skin contact must not exceed 0.5 µg/cm²/week.

Is cadmium banned in jewellery?

Metal parts of jewellery, imitation jewellery and hair accessories must contain less than 0.01% cadmium by weight of the metal, which in practice rules out deliberate use.

Do the same limits apply in the UK after Brexit?

Yes, for now. The restrictions were carried into UK REACH, which applies in Great Britain. The two lists can diverge over time, so check the HSE restrictions list for GB sales.

Does stainless steel jewellery need nickel testing?

Many stainless steels contain nickel, so you should have release test evidence for stainless steel items in prolonged skin contact rather than assume they pass.

Sources